Clik here to view.
Delta stage scanning not aligned to XY of camera
Hi, my delta stage is finally done and works. However, the movement in X and Y looks diagonal on the camera. Because of this, stitched images look odd: Is this intended or is my stage bugged? 7 posts...
View ArticleCallibrations Error
I am facing callibrations erros, after I installed and the software the I keep getting errors that there is missing callibration component. After I still process to the callibration the z motor moves...
View ArticleSangaboard v0.5.4. Error503: No stage connected
Hi, I tried to build high resolution microscope. When I run OpenFlexture Connect I get visual from camera but when i tired to move the stage I get “Error 503: No stage connected”. On Sangaboard RX...
View ArticleClik here to view.
Stage Limits and Mechanism
Hi all, I am trying to understand the limits of motion of the stage. What actually breaks or prevents excessive motion in the X and Y directions? For example if I keep driving in the +X direction what...
View ArticleClik here to view.
What is this bright spot in my picture?
On the left side of my photo here, there seems to be a bright spot. What do you think is wrong with my optical setup? I got a kit that came with 3 light diffusers. I put them in my illuminator. The...
View ArticleBright Black Screen Issue with OpenFlexure Microscope Software
Hi evryone, Bright Black screen appears when I try to use the OpenFlexure microscope software. The device powers on, but the screen stays blank, and I can’t proceed. Has anyone encountered this issue...
View ArticleIs this the correct specs for a LM objective?
ebay LM Plan 50x 7 posts - 3 participants Read full topic
View ArticleClik here to view.
Using Nikon Plan Fluor 10x 0.3
I already have this and would like to try it out, but realised it doesn’t an RMS thread, and instead uses an M25x0.75 thread. It also focuses at infinity. Can these be accommodated for by changing...
View ArticleClik here to view.
XY trnaslation flexture two knobs on one side
Hi all, I want to design a XY Flexure Adjustment Plate, that has two knobs on ONE side. Thorlabs has design that both knobs are prependicualr but due to space constraints I cannot leverage that...
View ArticleAnyone active in Delhi?
I’ve been speaking to a clinical collaborator who is interested in finding someone who could build/make/maintain an OpenFlexure Microscope as part of a study. If you’re close, please shout! 1 post - 1...
View ArticleUsing an ESP32 in the motor workaround?
I happen to have a bunch of esp32-c3 boards lying around and was wondering whether they would work to control the stage motors (which have not yet arrived). I’m able to modify the code as needed but...
View ArticleClik here to view.
OpenFlexure v7 - Is Top Layer Pillowing an issue?
Hello everyone, I’ve recently started my first build of the OpenFlexure v7. After getting the leg_test print bridges looking ok, I decided to do a couple test prints of the condenser and stage clips....
View ArticleClik here to view.
I made a sangaboard V0.5
I don’t know anything about software installation. What should I do next after I finish making sangaboard V0.5? Are there any detailed steps to teach me how to do it step by step? GitLab also...
View ArticleOptics module length
I have been experimenting with different objectives lately. The recommended 40x Plan objective with the f50d13.stl works very well. Finding an inexpensive 60x with the same characteristics is a...
View ArticleHow to Extend Exposure Time than limit in OpenFlexure Software?
Hi everyone, I’m currently using the OpenFlexure software to control a Raspberry Pi camera. While the Raspberry Pi camera itself supports exposure times of up to 11 seconds, I’ve noticed that the...
View ArticleIs there a Openflexure mirror that comes with Python 3.9/64-bit architecture...
Hi not sure if anyone has asked about this before but it’s been causing me a bit of a headache the last couple of days. I am trying to write some python code which will use the cellpose package for...
View ArticleClik here to view.
Objective Lens and other problems
My image in openflexure which I just built from iorodeo like a black square with a 1 inch white circle in it. I used an objective lens that is 10x it’s an amscope 10 .25 160 .17. I was expecting to...
View ArticleControlling movement and illumination and camera through an extension?
Are there extensions already built that I could use to control the movement, camera settings, and illumination intensity, or do I have to build my own. Do extensions add functionality and GUI elements...
View ArticleTimelapse extension
I made a little timelapse extension following the documentation and the example there (OpenFlexure eV GUI — OpenFlexure Microscope Software documentation) However, I got some sort of error that the...
View ArticleClik here to view.
Improve Delta Stage (reflection mode) image quality
We’re trying to improve the image quality from a Delta Stage Microscope in reflection mode (based on Test out optical microscopy on some dropcast battery slurry samples · Issue #142 ·...
View Article